![]() Better still, be quiet! uses a block front panel connector, so there’s no need to reach for the motherboard manual to recall where P LED and POWER SW are supposed to go. Simply attach the SATA power connector and four-pin fan header and you’re good to go. All the supplied fans are pre-wired to an eight-way ARGB/PWM hub attached to the rear of the motherboard tray, taking all the hassle out of wiring. Cable-routing holes, while not grommeted, are in plentiful supply – including a long void atop the PSU shroud – and there’s over 30mm clearance for cable clutter around back. That aside, Shadow Base 800 FX is an absolute breeze to build into on account of there being so much room to manoeuvre. I’ve lost count of how many times such notches have warped or broken under my watch, and on panels of this size, it’s a bit of a faff having to get everything perfectly aligned in order to slide securely into place. ![]() Effortless BuildĪ vast glass side panel ensures a clear view of all hardware, but it’s a shame be quiet! continues to use notches and captive thumb screws as opposed to push-to-lock latches and a quick-release mechanism. Sound dampening on a mesh-laden, airflow-optimised case is always tricky to implement, yet be quiet! covers the basics with a sheet of sound-absorbing material on the rear side panel, and bundled rubberised standoffs for hard-disk installation.Įvery contribution makes a difference and we thank you for your support. The top has a full-size magnetic filter, a mesh filter lining the base of the case pulls out from the front, and the trio of 140s protruding behind the bevelled fascia is covered with a magnetic filter that clips neatly into place. The front radiator will need to be less than 40mm thick in a dual-420 setup, but if you opt against the top radiator, front clearance extends to 66mm, leaving ample scope for a push-pull configuration.Īs you would expect from a be quiet! solution, there’s decent filtration and sound-dampening right out of the box. Spacing is such that there’s provision for not one but two 420mm liquid coolers in tandem. The top and front of the case can accommodate three 120/140s, in addition to a rear 120/140 and another on the bottom floor. The fact that four high-quality Light Wings 4 140mm PWM fans are included is a bonus – the RGB contrasts wonderfully with the white frame – but it’s the ability to expand that will appeal to hardened enthusiasts. Motherboard compatibility stretches to E-ATX with ease, graphics cards can measure up to 430mm in length, there’s a massive 180mm clearance for CPU cooling, and it doesn’t really matter how long your power supply is – the dedicated compartment has room to spare.Ĭooling opportunities are plentiful, too. The base model will fetch £145, DX starts at £160, and if you happen to fancy the RGB goodness of an all-white FX, prepare to stump up £205 of your hard earned. Shadow Base 800 FX, available in black or full-white (pictured), swaps the three Pure Wings 3 for a quartet of Light Wings 140mm ARGB fans alongside an eight-way hub.Īlways good to see plenty of choice, but there is an inevitable premium for those added niceties.Shadow Base 800 DX, available in black or white with black highlights and includes the same three Pure Wings 3 140mm PWM fans as well as ARGB LEDs lining the front panel.Shadow Base 800, which comes only in black and includes a trio of Pure Wings 3 140mm PWM fans.The Shadow Base 800 Series is available in five unique flavours: We’ll get to that shortly, but firstly, let’s talk variations. Hot off the press is the Shadow Base 800, a high-airflow case aimed squarely at users wanting to take cooling to the next level. After a relatively quiet 2022 (excuse the pun), the German manufacturer’s production lines are in full swing, with new coolers, power supplies and cases all headed our way. Jump to: Specification | Build Process | Conclusion
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |